Publications are to include the following acknowledgement:
This work was supported by the SUMA2 Network Project, 7th Framework Program of the European Commission (IRSES Project N° 318903).

Peer-reviewed journals

1. E.L. Dalibon, R. Charadia, A. Cabo, V. Trava-Airoldi, S.P. Brühl. Evaluation of the mechanical behaviour of a DLC film on plasma nitrided AISI 420 with different surface finishing. Surf Coat Tech 235 (2013) 735-740. http://dx.doi.org/10.1016/j.surfcoat.2013.08.059

2. E.A. Ochoa, R. Droppa, R.L.O. Basso, M. Morales, S. Cucatti, L.F. Zagonel, T. Czerwiec, M.C. dos Santos, C.A. Figueroa, F. Alvarez. The effect of noble gas bombarding on nitrogen diffusion in steel. Mat Chem Phys 143(2013), 116-123. http://dx.doi.org/10.1016/j.matchemphys.2013.08.027

3. W. Chamorro , D. Horwat , P. Pigeat , P. Miska , S. Migot , F. Soldera , P. Boulet , F. Mücklich. Near-room temperature single-domain epitaxy of reactively sputtered ZnO films. Journal of Physics D - Applied Physics 46 (2013) 235107. DOI:10.1088/0022-3727/46/23/235107

4. L. Escalada, S. P. Brühl, S. N. Simison. Microscopic investigation of pitting corrosion in plasma nitrided austenitic stainless steel. Pract. Metallography 51 (2014) 689-698. DOI:10.3139/147.110303

5. E.L. Dalibon, V. Trava-Airoldi, L.A. Pereira, A. Cabo, S.P. Brühl. Wear resistance of nitrided and DLC coated PH stainless steel. Surf. Coat. Tech. 255 (2014) 22-27. DOI:10.1016/j.surfcoat.2013.11.004

6. M.A. Guitar, E. Ramos-Moore, F. Mücklich. The influence of impurities on the formation of protective aluminium oxides on RuAl thin films. J. Alloys Comp. 594 (2014) 165-170. DOI:10.1016/j.jallcom.2014.01.137

7. S. Suarez, A. Rosenkranz, C. Gachot, F. Mücklich. Enhanced tribological properties of MWCNT/Ni bulk composites - Influence of processing on friction and wear behavior. Carbon 66 (2014) 164-171. http://dx.doi.org/10.1016/j.carbon.2013.08.054

8. S. Suarez, E. Ramos-Moore, B. Lechthaler, F. Mücklich. Grain growth analysis of multiwalled carbon nanotube-reinforced bulk Ni composites. Carbon (2014) http://dx.doi.org/10.1016/j.carbon.2013.12.089

9. E. Ramos-Moore, C. Espinoza, R.S. Coelho, H. Pinto, P. Brito, F. Soldera, F. Mücklich, J. Garcia. Investigations on thermal stresses of a graded Ti(C,N) coating deposited on WC-Co hardmetal. Adv. Mater. Research 996 (2014) 848-854. DOI:10.4028/www.scientific.net/AMR.996.848

10. M. Broglia, S. Suarez, F. Soldera, F. Mücklich, C.A. Barbero, R. Bellingeri, F. Alustiza, D. Acevedo. Direct laser interference patterning of polystyrene films doped with azo dyes, using 355 nm laser light. Appl. Surf. Sci. 300 (2014) 86-90. DOI: 10.1016/j.apsusc.2014.02.008

11. P. Cavallo, R. Coneo Rodriguez, M. Broglia, D.F. Acevedo, C.A. Barbero. Simple fabrication of active electrodes using direct laser transference. Electrochimica Acta 116 (2014) 194– 202. DOI: 10.1016/j.electacta.2013.10.146

12. S. Bongiovanni Abel, M. Molina, C. Rivarola, M. Kogan, C. Barbero. Smart polyaniline nanoparticles with thermal and photothermal sensitivity, Nanotechnology 25 (2014) 495602. DOI:10.1088/0957-4484/25/49/495602

13. M. Freislebem, C. Menezes, F. Cemin, F. Costi, P. Ferreira, C. Aguzzoli, I. Baumvol, F. Alvarez, C. Figueroa. Influence of the chemical surface structure on the nanoscale friction in plasma nitride and post-oxidized ferrous alloys. Applied Physics Letters 105 (2014) 111603. DOI: 10.1063/1.4894803

14. F. Cemin, L. Bim, C. Menezes, C. Aguzzoli, M. da Costa, I. Baumvol, F. Alvarez, C. Figueroa. On the hydrogenated silicon carbide (SiCx:H) interlayer properties prompting adhesion of hydrogenated amorphous carbon (a-C:H) deposited on steel. Vacuum 109 (2014) 180-183. DOI: 10.1016/j.vacuum.2014.07.015

15. Y. Wang, P. Miska, D. Pilloud, D. Horwat, F. Mücklich, J.F. Pierson. Transmittance enhancement and optical band gap widening of Cu2O thin films after air annealing. J. Appl. Phys. 115 (2014) 073505. DOI: 10.1063/1.4865957

16. Y. Wang, J. Ghanbaja, F. Soldera, P. Boulet, D. Horwat, F. Mücklich, J.F. Pierson. Controlling the preferred orientation in sputter-deposited Cu2O thin films: Influence of the initial growth stage and homoepitaxial growth mechanism. Acta Materialia 76 (2014) 207–212. DOI: 10.1016/j.actamat.2014.05.008

17. R. Rivero, M. A. Molina, C. R. Rivarola, C.A. Barbero. Pressure and microwave sensors/actuators based on smart hydrogel/conductive polymer nanocomposite. Sensors and Actuators B: Chemical 190 (2014) 270-278. DOI:10.1016/j.snb.2013.08.054

18. P. Cavallo, D. Acevedo, M. Fuertes, G. Soler-Illia, C. Barbero. Understanding the sensing mechanism of polyaniline resistive sensors. Effect of humidity on sensing of organic volatiles, Sensors & Actuators: B. Chemical (2015) 574–580. DOI:10.1016/j.snb.2015.01.029

19. N. Souza, M. Zeiger, V. Presser and F. Mücklich. In situ tracking of defect healing and purification of single-wall carbon nanotubes with laser radiation by time-resolved Raman spectroscopy. RSC Adv.(2015) DOI: 10.1039/C5RA09316C Open Access>

20. E. L. Dalibón, M. A. Guitar, V. Trava-Airoldi, F. Mücklich and S. P. Brühl. Nitriding and DLC Coatings for Corrosion Protection of Precipitation Hardening Stainless Steel. Advance Engineering Materials. DOI: 10.1002/adem.201500411

21. E. L. Dalibón, D. Heim, C. Forsich, A. Rosenkranz, M. A. Guitar, S. P. Brühl. Characterization of thick and soft DLC coatings deposited on plasma nitrided austenitic stainless steel. Diamond and Related Materials, 59 (2015), 73–79. DOI:10.1016/j.diamond.2015.09.010

22. S. Cucatti , E.A. Ochoa , M. Morales , R. Droppa , J. Garcia , H.C. Pinto , L.F. Zagonel , D. Wisnivesky , C.A. Figueroa , F. Alvarez. Effect of bombarding steel with Xe+ ions on the surface nanostructure and on pulsed plasma nitriding process Materials Chemistry and Physics (2015)261-269. DOI.10.1016/j.matchemphys.2014.10.015

23. F. Cemin , L. T. Bim , L. M. Leidens , M. Morales , I. J. R. Baumvol , F. Alvarez , C. A. Figueroa. Identification of the Chemical Bonding Prompting Adhesion of a-C:H Thin Films on Ferrous Alloy Intermediated by a SiC x :H Buffer Layer ACS Applied Materials and Interfaces (2015)15909-15917. DOI.10.1021/acsami.5b03554

24. F. Cemin , L.T. Bim , C.M. Menezes , M.E.H. Maia da Costa , I.J.R. Baumvol , F. Alvarez , C.A. Figueroa. The influence of different silicon adhesion interlayers on the tribological behavior of DLC thin films deposited on steel by EC-PECVD Surface and Coatings Technology (2015)115-121. DOI.10.1016/j.surfcoat.2015.10.031

25. S. Eckhardt, L. Müller-Meskamp, M. Loeser, M. Siebold, A. F. Lasagni. Fabrication of highly efficient transparent metal thin film electrodes using Direct Laser Interference Patterning Proceedings of SPIE - The International Society for Optical Engineering (2015)935116. DOI:10.1117/12.2082537

26. R. E. Rivero , F. Alustiza , N. Rodríguez , P. Bosch , M. C. Miras , C. R. Rivarola , C. A. Barbero. Effect of functional groups on physicochemical and mechanical behavior of biocompatible macroporous hydrogels Reactive and Functional Polymers (2015)77-85. DOI.10.1016/j.reactfunctpolym.2015.10.011

27. E. L. Dalibon , M. Moscatelli , S. Simison , L. Escalada , A. Cabo , C. Lasorsa , S. P. Brühl. Corrosion Behaviour of a SiOxNy Coated and Nitrided PH Stainless Steel Procedia Materials Science (2015)29-38. DOI.10.1016/j.mspro.2015.04.045

28. A. Gasco Owens , S. Brühl , S. Simison , C. Forsich , D. Heim. Comparison of Tribological Properties of Stainless Steel with Hard and Soft DLC Coatings Procedia Materials Science (2015)246-253. DOI.10.1016/j.mspro.2015.04.031

29. E.L. Dalibon , D. Heim , Ch. Forsich , S.P. Brühl. Mechanical Behavior of Nitrided 316L Austenitic Stainless Steel Coated with a:C-H-Si Procedia Materials Science (2015)163-170. DOI.10.1016/j.mspro.2015.04.021

30. Y. Wang , J. Ghanbaja , F. Soldera , S. Migot , P. Boulet , D. Horwat , F. Mücklich , J.F. Pierson. Tuning the structure and preferred orientation in reactively sputtered copper oxide thin films Applied Surface Science (2015)85-91. DOI.10.1016/j.apsusc.2015.02.028

31. M. F. Broglia, D. F. Acevedo, D. Langheinrich, H. R. Perez-Hernandez, C. A. Barbero, A. F. Lasagni. Rapid Fabrication of Periodic Patterns on Poly(styrene-co-acrylonitrile) Surfaces Using Direct Laser Interference Patterning, International Journal of Polymer Science (2015), Article ID 721035. DOI: 10.1155/2015/721035

32. F.Lasserre, A. Rosenkranz, N. Souza Carmona, M. Roble, E. Ramos-Moore, D. E. Diaz-Droguett, F. Mücklich, Simultaneous deposition of carbon nanotubes and decoration with gold–palladium nanoparticles by laser-induced forward transfer, Applied Physics A: Materials Science & Processing (2016), 150. DOI: 10.1007/s00339-016-9682-x

33. E. L. Dalibón, , M. A. Guitar, V. Trava-Airoldi, F. Mücklich, S. P. Brühl. Plasma Nitriding and DLC Coatings for Corrosion Protection of Precipitation Hardening Stainless Steel. Adv. Eng. Mater. (2016), 18: 826–832. DOI: 10.1002/adem.201500411

34. M. Soldera, K. Taretto, J. Berger, A. F. Lasagni. Potential of Photocurrent Improvement in µc-Si:H Solar Cells with TCO Substrates Structured by Direct Laser Interference Patterning. Adv. Eng. Mater. (2016), 18: 1674–1682. DOI: 10.1002/adem.201600225

35. F. Cemin, C. D. Boeira, C. A. Figueroa. On the understanding of the silicon-containing adhesion interlayer in DLC deposited on steel. Tribology International 94 (2016) 464–469. DOI: 10.1016/j.triboint.2015.09.044

36. N. Souza, F. Lasserre, A. Blickley, M. Zeiger, S. Suárez, M. Duarte, V. Presser ,F. Mücklich. Upcycling spent petroleum cracking catalyst: pulsed laser deposition of single-wall carbon nanotubes and silica nanowires. RSC Adv. 6 (2016) 72596-72606. DOI: 10.1039/C6RA15479D

37. E. R. Petry, C. D. Boeira, F. Cemin, L. M. Leidens, L. T. Bim, D. G. Larrude, M. E. H. Maia da Costa, C. A. Figueroa. Physicochemical structure of SiCx:H to improve DLC adhesion on steel. Surface Engineering 32 (2016) 779-785. DOI: 10.1080/02670844.2016.1159277

38. C. M. Menezes, N. Bogoni Jr., J. Barrirero, H. Aboulfadl, F. Mücklich, C. A. Figueroa. Influence of the surface chemistry-structure relationship on the nanoscale friction of nitrided and post-oxidized iron. Surface and Coatings Technology (2016) In Press. DOI: 10.1016/j.surfcoat.2016.07.095

Conferences

1. Charadia R., Cimetta J., Dalibon E.L., Brühl S.P. ¿La nitruración iónica puede ser un tratamiento de corta duración? Parámetros y resultados comparativos en un acero AISI 420. SAM Conamet - Congreso Internacional de Ciencia y Tecnología de Metalurgia y Materiales, August 20th-23rd 2013, Argentina. (Published in spanish in Conference Proceedings).

2. Dalibon E.L., Moscatelli M., Simison S., Escalada L., Cabo A., Lasorsa C., Brühl S.P. Comportamiento a la corrosión de un acero endurecible por precipitación nitrurado y recubierto con SiOxNy, SAM Conamet - Congreso Internacional de Ciencia y Tecnología de Metalurgia y Materiales, August 20th-23rd 2013, Argentina. (Published in spanish in Conference Proceedings).

3. Dufrène S. M. M., Cemin F., Soares M. F., Aguzzoli C., Maia da Costa, Baumvol I. J. R., Figueroa C. A. Amorphous hydrogenated carbon thin films deposited by segmented hollow cathode. PBII&D 2013, The 12th International Workshop on Plasma Based Ion Implantation and Deposition, Poitiers, France, 1-5 July 2013. Invited Talk.

4. Trentin R. E., Bandeira A. L., Amorim C. L. G., Aguzzoli C., Baumvol I. J. R., Moré Farias M. C., Figueroa C. A.. Physicochemical, Mechanical and Tribological Properties of Si3N4-MoS2 Thin Films Deposited by Magnetron Sputtering. ICMCTF2013, San Diego, USA. Oral presentation.

5. Escalada L., Brühl S.P., Suárez S., Guitar M.A., Manova D., Mändl S., Simison S. Efecto de las inclusiones en la morfología del ataque localizado en acero AISI 316L nitrurado con técnicas asistidas por plasma, SAM Conamet - Congreso Internacional de Ciencia y Tecnología de Metalurgia y Materiales, August 20th-23rd 2013, Argentina. (Published in spanish in Conference Proceedings).

6. Dalibon E., Charadia R., Cabo A., Trava-Airoldi V., Brühl S.P. Comportamiento mecánico de un recubrimiento DLC depositado sobre acero inoxidable martensítico previamente nitrurado. Proc. Second International Workshop of Tribology “TriBaires 2013”, Buenos Aires, Argentina May 7-9 2013.

7. Vaca L.S., Márquez A., Brühl S.P. Microstructure and corrosion behaviour of ion nitrided AISI 316L coated with titanium nitride. PBII&D 2013, The 12th International Workshop on Plasma Based Ion Implantation and Deposition, Poitiers, France, 1-5 July 2013.

8. L. Escalada L., Simison S. N., Manova D., Mändl S., Neumann H., Dalibon E. L., Vaca L. S., Brühl S. P. Comparison of wear and corrosion behavior of three different nitriding methods on AISI 316L stainless steel. PBII&D 2013, presented in 12th International Workshop on Plasma Based Ion Implantation and Deposition, Poitiers, France, 1-5 July 2013.

9. Vaca L.S., Brühl S.P., Márquez A. Comportamiento al desgaste de AISI 316L nitrurado por plasma y recubierto con TiN. SAM Conamet - Congreso Internacional de Ciencia y Tecnología de Metalurgia y Materiales, August 20th-23rd 2013, Argentina. (in Spanish).

10. Escalada L., Brühl S.P., Suarez S., Guitar A., Manova D., Mändl S., Simison S. Influence of inclusions on the corrosion attack of plasma nitrided austenitic stainless steel. FEMS Congress Euromat 2013, European Congress and Exhibition on Advanced Materials and Processes, Sevilla, Spain, September 8-13 2013.

11. Coneo Rodriguez R., Cavallo P.C., Acevedo D.F., Planes G.A., Barbero C.A. Fabrication of electrochemical sensors using direct laser transfer. 3rd International conference on materials and applications for sensors and transducers, Prague, Czech Republic, September 13-17 2013.

12. K. Taretto; A. Koffman-Frischknecht; M. Soldera. Light and dark current-voltage fits of bulk heterojunctino cells using a new analytical drift-diffusion model. 25th European Photovoltaic Solar Energy Conference and Exhibition. WIP Renewable Energies, subject 3DV.2.8, 2013.

13. A. Cabo, V. Trava-Airoldi, L.A. Pereira, E.L. Dalibon, S.P. Brühl. Corrosion resistance of DLC hard coatings deposited over nitrided PH stainless steel. Pan American Materials Conference 2014/69th ABM Conference, São Paulo (BR), July 21tst-25th 2014.

14. S.P. Brühl, E.L. Dalibon, D. Heim, C. Forsich. Characterization of thick and soft DLC coatings deposited on plasma nitrided stainless steel. Plasma Surface Engineering Conference 2014, Garmisch-Partenkirchen (DE) September 15th-19th 2014.

15. D. Manova, S. Mändl, S.P. Brühl, L. Escalada, S. Simison. Corrosion resistance of AISI 316L stainless steel nitrided by three different plasma assisted techniques. Workshop on Surface Treatments of Corrosion Resistant Alloys, within the frame of 69th ABM Conference, São Paulo (BR) July 21st-25th 2014.

16. E.L. Dalibon, D. Heim, C. Forsich, S.P. Brühl. Comportamiento mecánico del acero AISI 316L recubierto con a:C-H-Si previamente nitrurado. Congreso Internacional de Metalurgia y Materiales SAM-CONAMET 2014, Santa Fe (AR) October 21st-24th 2014.

17. L.S. Vaca, M. Moscatelli, A. Cabo, D. Manova, S.N. Simison, L. Escalada, S.P. Brühl. Resistencia al desgaste y corrosión de AISI 316L nitrurado por dos diferentes métodos asistidos por plasma. Congreso Internacional de Metalurgia y Materiales SAM-CONAMET 2014, Santa Fe (AR) October 21st-24th 2014.

18. L. Escalada, E.L. Dalibon, S.P. Brühl, S. Simison. Recubrimientos duros tipo DLC depositados sobre acero inoxidable martensítico nitrurado: análisis de adhesión y resistencia a la corrosion. Congreso Internacional de Metalurgia y Materiales SAM-CONAMET 2014, Santa Fe (AR) October 21st-24th 2014.

19. J. Berger, A. F. Lasagni, L. Müller-Meskamp, Y. Park, C. Fuchs: Laser Patterning of Transparent Conducting Oxide Layers for Optical Applications, Materials Science and Engineering (MSE) 2014, September 2014, Darmstadt, Germany.

20. J. Berger, A. Lasagni: Laser Interference Patterning of transparent conducting oxides, 3rd International Summer School "Trends and new developments in Laser Technology 2014", Technische Universität Dresden / Fraunhofer IWS, August 2014, Dresden.

21. S. Eckhardt, T. Roch, S. Schubert, A. Lasagni: Light management in metallic thin film electrodes by laser-assisted surface functionalization, 3rd International Summer School "Trends and new developments in Laser Technology 2014", Technische Universität Dresden / Fraunhofer IWS, August 2014, Dresden.

22. F. Lasserre, F. Mücklich, E. Ramos-Moore, P. Cavallo, D. F. Acevedo, C. A. Barbero. Laser induced forward transfer for the design of electronic noses. MSE Conference 2014, Darmstadt (DE), September 23rd-25th 2014.

23. F. Cemin, L.T. Bim, C.M. Menezes, C. Aguzzoli, M.E.H. Maia da Costa, I.J.R. Baumvol, F. Alvarez, and C.A. Figueroa. Temperature influence on the silicon interlayer growth for amorphous carbon films deposited on AISI 4140 steel by pulsed-DC PECVD. 14th International Conference on Plasma Surface Engineering, Garmisch-Partenkirchen, Germany, September 15-19 - 2014.

24. M. Freislebem, C. Menezes, F. Cemin, F. Costi, P. Ferreira, C. Aguzzoli, I. Baumvol, C. Figueroa. Friction behavior at the nanoscale of nitrided and post-oxidized plain steel. 41st International conference on metallurgical coatings and thin films, San Diego USA, April 21-25 2014.

25. Y. Wang, J. Ghanbaja, S. Migot, P. Boulet, P. Miska, D. Horwat, F. Soldera, F. Mücklich, J.F. Pierson. Growth of copper oxide thin films by reactive sputtering: control of the texture and structure-properties relationship. European Materials Research Society Conference (E-MRS 2014), Lille FR, May 26-30 2014.

26. Y. Wang, J. Ghanbaja, P. Boulet, D. Horwat, F. Soldera, F. Mücklich, J.F. Pierson. Tuning the preferred growth orientation in reactively sputtered copper oxide thin films. 14th International Conference on Plasma Surface Engineering – PSE 2014, Garmisch-Partenkirchen (Germany), September 15-19 2014.

27. Y. Wang, J. Ghanbaja, Y. Fagot-Revurat, D. Horwat, F. Soldera, F. Mücklich, J.F. Pierson. Structural, electrical and optical properties of reactively sputtered binary copper oxide thin films. European Materials Research Society Conference (E-MRS 2014 Fall-Meeting), Warsaw (Poland), September 15-19 2014.

28. Y. Wang, J. Ghanbaja, F. Soldera, A. Mézin, D. Horwat, F. Mücklich, J.F. Pierson. Influence of oxygen partial pressure on the functional properties of nickel oxide sputtered films. European Materials Research Society Conference (E-MRS 2014 Fall-Meeting), Warsaw (Poland), September 15-19 2014.

29. Y. Wang, J. Ghanbaja, F. Sodera, A. Mézin, D. Horwat, F. Mücklich, J.F. Pierson. Growth and characterization of reactively sputtered NiO thin films. 5th International Symposium on Transparent Conductive Materials (TCM), Platanias (Greece), October 12-17 2014.

30. Y. Wang, J. Ghanbaja, P. Boulet, D.Horwat, F. Soldera, F. Mücklich, J.F. Pierson. Electrical and optical properties of binary copper oxide thin films. 5th International Symposium on Transparent Conductive Materials (TCM), Platanias (Greece), October 12-17 2014.

31. J.F. Pierson, Y. Wang, J. Ghanbaja, Y. Fagot-Revurat, D. Horwat, F. Soldera, F. Mücklich. Towards an improvement of the functional properties of copper oxide thin films by the control of their composition and microstructure. 1er colloque franco-marocain sur les Energies Nouvelles et Renouvelables (COFMER’01) – Rabat (Morocco), October 28-30 2014.

32. W. Chamorro, S. Migot, P. Miska, P. Pigeat, F. Mücklich, F. Soldera, D. Horwat. Tuning of the microstructural and optical properties in ZnO thin films grown by reactive magnetron sputtering at room temperature. International Workshop on Nanomaterials, Nancy (France), September 8-11 2014.

33. N. Souza, V. Presser and F. Mücklich. Laser annealing of single-wall carbon nanotubes. NT14, Los Angeles, USA, 1-7 june 2014.

34. F. Cemin, L. T. Bim, C. M. Menezes, L. M. Leidens, M. E. H. Maia da Costa,C. Aguzzoli, F. Alvarez, C. A. Figueroa, Influence of the physicochemical structure of a SiCx:H interlayer on the tribological behavior of a-C:H thin films grown on steel by EC-PECVD. 42th International Conference on Metallurgical Coatings and Thin Films, San Diego-CA, EUA, April 20-24 - 2015.

35 L. Milschi, I. Belahsen, G. C. Lain, E. R. Petry, F. Cemin, J. Catafesta, C. A. Figueroa, TiCxNy Thin Films for Decorative Applications Produced by Cathodic Arc Deposition. 58th Annual Meeting of the Society of Vaccum Coaters, Santa Clara-CA, EUA, April 26 to May 01 - 2015.

36. J. Berger, A. Lasagni, M. Soldera, K. Taretto, L. Müller-Meskamp, Y. Park, C. Fuchs, Optimierung von Solarzellen durch direkte Laserinterferenzstrukturierung. Poster, Werkstoffwoche Dresden, 2015.

37. T. Czerwiec, A. Andrieux, G. Marcos, Surface patterning by plasma: principle and applications, 13th International Conference on Plasma Based Ion Implantation & Deposition, PBII&D 2015, Buenos-Aires, Argentina, October 5-9, 2015.

38. A. Andrieux, G. Marcos, H. Michel, T. Czerwiec, On the different ways to achieve surface patterning of austenitic stainless steel by plasma, conference orale présentée à 20th International Colloquium on Plasma Processes, Saint-Etienne, France, June 1-5, 2015

39. C. A. Barbero, R. Coneo Rodriguez, D. F. Acevedo, G. A. Planes, Strong Catalytic Effect of Cobalt Oxide Nanoparticles on the Electrochemical Sensing of Arsenic, 17th Topical Meeting of the International Society of Electrochemistry, Saint-Malo, France, May 31 - June 3 , 2015

40. C. A. Barbero, G. A. Planes, G. García, E. Pastor,A. Baena Moncada, R. Coneo Rodriguez, P. Cappellari, Hierarchical Nanostructured Fuel Cell Electrodes Studied by In-situ Electrochemical Techniques, 17th Topical Meeting of the International Society of Electrochemistry, Saint-Malo, France, May 31 - June 3 , 2015